Project

                                 .  DBRT STUDENT 2017-2018 

                        VIGYAN ASHRAM
                        

   
Section name:- Energy and Environment
   Project name:- Electrical wiring 
    Project By      :- Shaikh soyal,RASHIK
    Guiders          :- Suyog sir
    Date of starting:-  21/01/2018

     Date of finishing:- 24/01/2018
      project

  Introduction            

  Why we do wiring in ancient period's we do not use electrical. In that period we use fire lamp like a light. In that period their are no electronic's and electricity in this period we do wiring for light and charging electronics devices.wiring is the process that wire should assembled in one circuit and we also use safety like fuse, board, switches,socket,wires,MCB. In that we  also use different types of tool,s nosed plier ,wire stripper, cutting plier, plumb bod, screw driver, line tester, hacksaw, insulation tape, hammer, drill machine we use this tools for electrical wiring.

Aim :- Electrical wiring 

Tool's :-    nosed plier ,wire stripper, cutting plier, plumb bod, screw driver, line tester, hacksaw, insulation tape, hammer, drill machine,linetube,rope,chock.

Planning :-We go to that place where we are going to do electrical wiring and take the electrical load.

S.no	NAME	LOAD
1	Book scanner	20.8 W
2	Computer	220 W
3	Computer	220 w
4	Sewing machine	60 W
5	Sewing machine	25 W
	TOTAL	545.8 W

  Procedure :-
  1) First we take perfect measurement with line tube for ha place where we are fitting patti and draw a line horizontally with a colored chock.
  2) After then we take 6 fit patti and put exact on a line and drill holes at one one 6 fit patti we drilled 3 holes and then screw of 25x8 and fitted it with screw driver.
   3) And we started fitting board fitting board's at computer and ups online connection we fitted 36 amperes board and then .After we fitted near two sewing machines and for first machine the 12 amperes board we fitted at second also. We fitted 12 amperes board at sewing  machine side we fitted 12 amp board at last we fitted at computer 24 amp board.
 4)Then we started giving connection's in board's that is given in above figure.
* Material's proper costing how much we use .
   

Materials	Rate	Quantity	Total
Poly cab wire red	22	20	440
Poly cab wire Blue	22	20	440
Poly cab wire Yellow	15	20	300
6 Amp MCB	120	1	120
MCB cover	25	1	25
6 by 4 board	140	1	140
25x8 screw	140	24	12
Fuse	25	3	75
Indicater	15	3	45
Holder	25	1	25
Led 9 watt bulb	170	1	170
Socket	25	16	400
Switch	20	17	340
Casing patti	49	9	441
4 by 2 board	120	4	480
TOTAL			5,275

Electrical point  9 x 60

                            540

Labor charge      1453.75 

Observation :-I observe that we fase problem's like in drilling and screw fitting the drilling has been donned in steel and screw's were tightly ging and short circuit at board we jointed the fase and neutral together and mcb is tripping. when we are on the mcb. we save the short circuit has not done because of mcb.


conclusion :-At last we fased all the problem's and solved and completed our work properly .

Result's :-result's are good we have done our work properly and perfectly.

Types of wiring information's :-
Industrial wiring 
House wiring

conclusion :-At last we fased all the problem's and solved and completed our work properly .

Result's :-result's are good we have done our work properly and perfectly.

Types of wiring information's :-
Industrial wiring 
House wiring